Manufacturer of Inov Polyurethane Waterproof Sealant Products for Ms Sealant and Ms Polymer
we could supply good quality goods, aggressive cost and very best purchaser assistance. Our destination is “You come here with difficulty and we supply you with a smile to take away” for Manufacturer of Inov Polyurethane Waterproof Sealant Products for Ms Sealant and Ms Polymer, We guaranteed high quality, if clients were not satisfied with the products’ quality, you can return inside 7days with their original states.
we could supply good quality goods, aggressive cost and very best purchaser assistance. Our destination is “You come here with difficulty and we supply you with a smile to take away” for China Polyurethane and Polyurethane Factory, Our company regards “reasonable prices, efficient production time and good after-sales service” as our tenet. We hope to cooperate with more customers for mutual development and benefits. We welcome potential buyers to contact us.
Technical Data
| Solid content | 75% |
| Imperme ability pressure | 0.8Mpa |
| Lateral Deformation Capability | 34.4mm |
| Compressive strength | 31.3Mpa |
| Flexural strength | 10.0Mpa |
| Shrinkage | 0.20% |
| Drying time | 1h30min |
| Country of origin | Made in China |
| Model NO. | BPR-7120 |
| Physical state | After mixing, it is a liquid with uniform color and no precipitation or water separation. |
Product Application
Product Instructions
Construction technology:
Base cleaning: Check if the base level is flat, solid, crack-free, oil-free, etc., and repair or clean if there is any problem. The base layer should have a certain water absorption and drainage slope, and the yin and yang corners should be rounded or sloped.
Base treatment: Wash with a water pipe to completely wet the base, keep the base moist, but there should be no clear water.
Coating preparation: according to the ratio of liquid material: powder = 1:0.4 (mass ratio), mix the liquid material and powder evenly, and then use it after standing for 5-10 minutes. Keep stirring intermittently during use to prevent layering and precipitation.
Paint brush: Use a brush or roller to paint the paint on the base layer, with a thickness of about 1.5-2mm, and do not miss the brush. If it is used for moistureproofing, only one layer is required; for waterproofing, two to three layers are required. The directions of each brush should be perpendicular to each other. After each brush, wait for the previous layer to dry before proceeding to the next brush.
Protection and maintenance: After the slurry construction is completed, the coating must be protected before it is completely dry to avoid damage from pedestrians, rain, sun exposure, and sharp objects. The fully cured coating does not require a special protective layer. It is recommended to cover with a damp cloth or spray water to maintain the coating, usually for 2-3 days. After 7 days of curing, a 24-hour closed water test should be carried out if conditions permit.”
Tool cleaning: Please use clean water to wash all utensils on time after stopping in the middle of painting and after painting.
Dosage: Mix slurry 1.5KG/1㎡ two times
Packaging specification: 18KG
Storage method: Store in a cool and dry warehouse at 0°C-35°C, avoid rain and sun exposure, and strictly prevent frost. Avoid stacking too high.
Points to Attention
Construction and use suggestions
1. Carefully read the instructions for using this product before construction.
2. It is recommended to try it in a small area first, and if you have any questions, please consult on time before using it.
3. Avoid storage at low temperatures or exposure to sunlight.
4. Use according to product technical instructions.
Executive standard
JC/T2090-2011 Building Waterproof Standard
Product construction steps
Product Display
we could supply good quality goods, aggressive cost and very best purchaser assistance. Our destination is “You come here with difficulty and we supply you with a smile to take away” for Manufacturer of Inov Polyurethane Waterproof Sealant Products for Ms Sealant and Ms Polymer, We guaranteed high quality, if clients were not satisfied with the products’ quality, you can return inside 7days with their original states.
Manufacturer of China Polyurethane and Polyurethane Factory, Our company regards “reasonable prices, efficient production time and good after-sales service” as our tenet. We hope to cooperate with more customers for mutual development and benefits. We welcome potential buyers to contact us.
